Forget the error leaving the form, I fixed it.
Back to the tables, if I create a new table before the table that works fine, this new table will have the error of List index.
Add text with different formats in a cell
-
- Site Admin
- Posts: 17522
- Joined: Sat Aug 27, 2005 10:28 am
- Contact:
-
- Site Admin
- Posts: 17522
- Joined: Sat Aug 27, 2005 10:28 am
- Contact:
-
- Posts: 20
- Joined: Fri Jun 03, 2011 8:33 pm
TList.Error('List index out of bounds (%d)',-60)
TList.Error($41D53C,-60)
TList.Get(-60)
TRVTableRow.Get(???)
TRVTableRows.GetMainCell(3,-60,3,-60)
TSRichViewEdit.checkTable(???,242,387,???)
TSRichViewEdit.MouseMove([],266,282)
TControl.WMMouseMove((512, 0, 266, 282, (266, 282), 0))
TControl.WndProc((512, 0, 18481418, 0, 0, 0, 266, 282, 0, 0))
TWinControl.WndProc((512, 0, 18481418, 0, 0, 0, 266, 282, 0, 0))
TSRichViewEdit.WndProc((512, 0, 18481418, 0, 0, 0, 266, 282, 0, 0))
TWinControl.MainWndProc((512, 0, 18481418, 0, 0, 0, 266, 282, 0, 0))
StdWndProc(396010,512,0,18481418)
TApplication.ProcessMessage((396010, 512, 0, 18481418, 3639300, (755, 581)))
TApplication.HandleMessage
TApplication.Run
ULTRASIS_SGLI
TList.Error($41D53C,-60)
TList.Get(-60)
TRVTableRow.Get(???)
TRVTableRows.GetMainCell(3,-60,3,-60)
TSRichViewEdit.checkTable(???,242,387,???)
TSRichViewEdit.MouseMove([],266,282)
TControl.WMMouseMove((512, 0, 266, 282, (266, 282), 0))
TControl.WndProc((512, 0, 18481418, 0, 0, 0, 266, 282, 0, 0))
TWinControl.WndProc((512, 0, 18481418, 0, 0, 0, 266, 282, 0, 0))
TSRichViewEdit.WndProc((512, 0, 18481418, 0, 0, 0, 266, 282, 0, 0))
TWinControl.MainWndProc((512, 0, 18481418, 0, 0, 0, 266, 282, 0, 0))
StdWndProc(396010,512,0,18481418)
TApplication.ProcessMessage((396010, 512, 0, 18481418, 3639300, (755, 581)))
TApplication.HandleMessage
TApplication.Run
ULTRASIS_SGLI
-
- Posts: 20
- Joined: Fri Jun 03, 2011 8:33 pm
-
- Site Admin
- Posts: 17522
- Joined: Sat Aug 27, 2005 10:28 am
- Contact:
-
- Posts: 20
- Joined: Fri Jun 03, 2011 8:33 pm
-
- Site Admin
- Posts: 17522
- Joined: Sat Aug 27, 2005 10:28 am
- Contact: